Atsg 4l60e rebuild manual free download.THM 4LE – ATSG (Automatic Transmission Service Group) – PDF Download

Looking for:

Atsg 4l60e rebuild manual free download 

Click here to DOWNLOAD

   

 

ATSG TRANSMISSION MANUALS FULL - Automotive Library.Atsg 4l60e rebuild manual free download

  ATSG (Automatic Transmission Service Group) transmission manuals are a collection of manuals for rebuilding transmissions from ATSG. General Motors. TH Transmissions - TH (M34) 3T40, THC (MD9) Saturn TAAT - Saturn Transmission - TAAT - FWD 4 Speed. A, GM MX17 - . FORD 4R The Ford 4R transmission is an updated version of the E4OD and was first introduced in the model year, and is currently found in the F, F, F and F Super Duty trucks, E, E, E, E vans and the Expedition/Navigator/Excursion vehicles equipped with the L, L, and L engines. Mar 03,  · Can't be any worse than the $30 ATSG manual than hasn't been updated since You have to buy both the manual and Update Handbook (another $30) to get current info. Men can only be highly civilized, if other men deemed less civilized, are there to guard and feed ted Reading Time: 1 min. The ATSG 4L60 (R4) Technical Manual covers assembly, dis-assembly, diagnosis, and troubleshooting. Note: There have been many engineering changes in this transmission since its introduction. ATSG also has available an "Update Handbook" which includes the many changes and is required along with this manual for a proper overhaul or THM 4LE/4LE “UPDATE HANDBOOK” – ATSG PDF. Since the introduction of the THM 4LE transmission in model year , there have been many major engineering design changes to improve durability and reliability.  

Atsg 4l60e rebuild manual free download.Popular manuals

 

Quick Links. Previous Page. Next Page. Microphone system ATSG Ford 4R transmissions on other models are not PTO capable. It is the manual gear shift lever, as shown in Figure 3. Page 7 The Double Arrow keys can also be This is the recommended used to manually raise or lower the method of elevating idle engine speed at a faster or slower speed for PTO operations. Page 9 The Park Gear is also a press fit to the output shaft, and the number 13 thrust washer, between the case and the park gear has been replaced with a needle bearing.

Page 10 Testing the neutral start circuit is done across pins 10 and 12 of the DTR sensor, and must be checked in each selector position to determine switch integrity. Refer to Figure Before adding any fluid, ensure that it Firm shifts P normal manner, which may cause a and engagements.

May flash TCIL. P transmission concern. Refer to shift solenoid operation chart. P signal intermittent. Failed Off: No third gear engine braking in O. Failed On: Third gear engine braking in O. Coast clutch may be damaged causing eventual failure. Install a psi line pressure gauge to the line performing the "Stall" Page 29 I. Page Transmission Disassembly 5. Set the main upper and lower valve bodies aside for the component rebuild section. Continued on Page Page 43 Figure Remove the solenoid body screen from spacer plate, as shown in Figure 52, by rotating and lifting straight up.

Page 51 Remove the snap ring from case, as shown in Figure Page 53 Figure Page 56 Continued on Page Page 57 Continued on Page Page 58 Continued on Page Page 59 Continued on Page Page 60 Page 71 "Late" design sun shell will retro-fit back on all models. Page 72 7. Page 75 1. Page 78 Note: Black side faces up.

Install the complete forward planetary carrier assembly into the ring gear, by rotating into position, as shown in Figure Page 79 Figure Page 81 Continued on Page Disassemble overdrive gearset using Figure 4.

Page 85 Technical Service Information Ensure that snap ring is fully seated. Place the coast clutch housing on a flat work surface, as shown in Figure Page 92 0. Page 96 7. Set the completed pump body aside for the Figure future sub-assembly See Figure Turn the oil pump cover over and install the Page 6 o'clock bottom position in case.

Page 1. Page Continued on Page Figure Page Manual Shift Lever Differences or equivalent. Page 6. Install the cooler bypass valve with the sealing washers positioned as shown in Figure , and install threaded cooler line case fittings. Remove the transmission from bench fixture Install torque converter and check the seating and set on flat work surface See Figure Solenoid to Main V.

Print page 1 Print document pages. Cancel Delete. Sign In OR. Don't have an account? Sign up! Restore password. Upload from disk.

Upload from URL.